所提供的轴承产品全部品质保障。珍惜您的设备,欢迎新老客户前来订购!
联系我们
    鸿御(上海)国际贸易有限公司
    电话:021-56036899
    传真:021-56036877
    手机:13311666672
    QQ:524085168
    邮箱:china_bearing@163.com
    地址:上海市静安区共和新路425号
扬州INA轴承轮毂轴承的监测过程 来源:御狮轴承   点击:次   日期:2018-08-05 23:49

  轮毂(形状:扬州INA轴承)是行走机械的重要载体。它有助于降低底盘的摩擦阻力,并保持车辆的正常行驶负荷。如果轮毂轴承(轴承)出现故障(故障),则会引起噪声、轴承发热等现象,尤其是前轮更加明显,容易引起(失控)失控等危险现象,危害人身安全(Wi-Hi)。因此,在使用轮毂轴承(轴承)时,定期检查是非常必要的,此外,维修也是一项重要工作,下面,我们将仔细加以说明。

The hub (shape: Yangzhou INA bearing) is an important carrier of walking machinery. It helps to reduce the friction resistance of the chassis and maintain the normal driving load of the vehicle. If the hub bearing (bearing) fails (the fault), it will cause noise, bearing fever and other phenomena, especially the front wheel more obvious, easy to cause (out of control) out of control and other dangerous phenomena, harm the personal safety (Wi-Hi). Therefore, in the use of hub Zhou Cheng (Zhou Cheng), regular inspection is very necessary, in addition, maintenance is also an important work, below, we will carefully explain.

1、检查车轮(形状:扬州INA轴承)轴承和轴承套圈,如疲劳剥落、裂纹或轴承滚子松动现象,或在寻找轴承座环点时,应更换轴承。凭借在INA轴承领域的丰富经验,INA拥有各种先进工程产品的开发、制造和应用所必需的知识和专长。小型扬州INA轴承如微型轴承,只有0.003克,大轴承高达三十四吨。

1, check the wheel (shape: Yangzhou INA bearing) bearing and bearing rings, such as fatigue peeling, cracks or bearing roller loosening, or when looking for the bearing seat ring point, the bearing should be replaced. With rich experience in the field of INA bearings, INA has the knowledge and expertise necessary for the development, manufacture and application of various advanced engineering products. Small Yangzhou INA bearings such as miniature bearings, only 0.003 grams, large bearings up to thirty-four tons.

2、轴承(轴承)腔应涂上扬州INA轴承润滑脂(注意),油脂应挤压到轴承上,直到油脂从轴承的另一侧排出。在轮毂和筒头上涂抹一层润滑脂,防止生锈。注意轮毂内的油脂,不要涂抹过多,否则会影响(散热)和刹车。

2。 Bearing (bearing) cavity should be coated with Yangzhou INA bearing grease (attention), grease should be extruded to the bearing, until the grease is discharged from the other side of the bearing。 Apply grease on wheel hub and cylinder head to prevent rust。 Pay attention to the grease inside the wheel, do not apply too much, otherwise it will affect (heat dissipation) and brake。

3、轮毂(形状:管子)扬州INA轴承(轴承)调节,行驶里程(约1OKM),停车检查,用来擦拭轮毂的温度,如热,调整轴承过紧,应重新调整,适当密封松弛轴承。INA轴承是由INA生产的轴承。INA轴承在全球轴承行业处于领先地位。由INA提供的标准产品包括超过20000个轴承。

3, hub (shape: pipe) Yangzhou INA bearing (bearing) adjustment, driving mileage (about 1OKM), parking inspection, used to wipe the temperature of the wheel hub, such as heat, adjusting the bearing is too tight, should be re adjusted, properly sealed loose bearings. The INA bearing is a bearing produced by INA. INA bearing is in the leading position in the global bearing industry. The standard products provided by INA include more than 20000 bearings.

 

文章来自:扬州SKF轴承 www.wh-skf.com

The article comes from: Yangzhou SKF bearing www.wh-skf.com

文章来自:扬州INA轴承 www.xzahg.com

The article comes from: Yangzhou INA bearing www.xzahg.com

文章来自:扬州NSK轴承 www.klbbearings.com

The article comes from: Yangzhou NSK bearing www.klbbearings.com

 

QQ524085168  

电话:0510-81207777

手机:13311666672

【声明】我站所发布的轴承文章,都是本公司技术原创,我公司对发布的文章拥有著作权,其余网站均不可抄袭,我公司将对抄袭的行为保留法律追究的权利。
点击次数:  更新时间:2018-08-05 23:49:09  【打印此页】  【关闭
关于我们 品牌展示
快乐赛车彩票靠谱吗 快乐赛车有没有分析的方法 快乐赛车如何计算6码 快乐赛车怎么样才能稳赢 快乐赛车福利彩票 快乐赛车规律公式 快乐飞艇计划有软件吗 快乐飞艇能玩吗 快乐赛车怎么样 快乐赛车微信群