所提供的轴承产品全部品质保障。珍惜您的设备,欢迎新老客户前来订购!
联系我们
    鸿御(上海)国际贸易有限公司
    电话:021-56036899
    传真:021-56036877
    手机:13311666672
    QQ:524085168
    邮箱:china_bearing@163.com
    地址:上海市静安区共和新路425号
江苏INA轴承异常温过的监测程序 来源:御狮轴承   点击:次   日期:2018-07-14 17:01

江苏INA轴承的温度通常是由轴承外部的温度来预测的。如果油孔能够直接测量轴承外圈的温度,则更为合适。

The temperature of INA bearings in Jiangsu is usually predicted by the temperature outside the bearing. If the oil hole can directly measure the temperature of the outer ring of the bearing, it is more appropriate.

通常,江苏INA轴承的温度随着轴承的运转而缓慢上升,1-2小时后达到稳定状态。江苏INA轴承的正常温度不同于机器的热容、散热、速度和负载。如果润滑和安装部件合适,江苏INA轴承温度将迅速升高,并且会出现异常高温。此时,必须停止手术,并采取必要的预防措施。

In general, the temperature of INA bearings in Jiangsu increases slowly with the operation of bearings, reaching a steady state after 1-2 hours。 The normal temperature of INA bearing in Jiangsu is different from the heat capacity, heat dissipation, speed and load of the machine。 If the lubrication and installation parts are suitable, the bearing temperature of Jiangsu INA will increase rapidly and there will be abnormal high temperature。 At this point, surgery must be stopped and necessary precautions should be taken。

热传感器的使用可以随时监测轴承的工作温度。当温度超过规定值时,可自动报警或停止燃烧轴事故。

The use of thermal sensors can monitor the working temperature of bearings at any time. When the temperature exceeds the specified value, it can automatically alarm or stop the burning shaft accident.

高温常表明轴承处于异常状态。高温对江苏INA轴承润滑剂也是有害的。有时轴承过热可归因于轴承的润滑剂。如果轴承温度超过125度,长期转移将降低轴承寿命。江苏INA轴承的原因包括润滑不足或过度润滑,润滑剂。它含有杂质、过载、轴承损坏环、间隙不足和油封引起的高摩擦。

The high temperature often indicates that the bearing is in an abnormal state. High temperature is also harmful to Jiangsu INA bearing lubricants. Sometimes the bearing overheat can be attributed to the lubricant of the bearing. If the bearing temperature exceeds 125 degrees, the long term transfer will reduce the bearing life. The reasons for INA bearings in Jiangsu include inadequate lubrication or excessive lubrication, lubricants. It contains impurities, overload, bearing damage ring, insufficient clearance and high friction caused by oil seal.

因此,江苏INA轴承温度的连续监测是必要的,而不考虑轴承本身或其他重要部件的测量。如果操作条件保持不变,温度的任何变化都可以指示故障。

Therefore, the continuous monitoring of INA bearing temperature in Jiangsu is necessary without considering the measurement of the bearing itself or other important parts。 If the operating conditions remain unchanged, any change in temperature can indicate failure。

江苏INA轴承温度的周期性测量可应用于温度计,如数字温度计,它能精确测量轴承温度并在单位温度或华氏温度下显示轴承温度。

The periodic measurement of the INA bearing temperature in Jiangsu can be applied to a thermometer, such as a digital thermometer, which can accurately measure the bearing temperature and display the bearing temperature at unit temperature or Fahrenheit temperature.

重要的轴承意味着设备在损坏时会被关闭,所以最好安装一个温度检测器。

Important bearings mean that the equipment will be shut down when damaged, so it is best to install a temperature detector.

通常,在润滑或再润滑之后,自然温度将上升并持续一到两天。

Normally, after lubrication or re lubrication, the natural temperature will rise and last for one to two days。

通常,工作温度超过150度的K轴承称为江苏INA轴承。含铬钢的硬度会急剧下降,尺寸将不稳定,因此轴承将不能正常工作,因为铬钢将使用超过150度。因此,对于江苏INA轴承,在工作温度为150350℃的条件下,如果普通高碳铬江苏INA轴承钢仍在环件和轧制体中制造,则必须对轴承部件进行特殊的回火,并且必须进行一般的回火。它比工作温度高50度。

Usually, the K bearing with a working temperature exceeding 150 degrees is called Jiangsu INA bearing. The hardness of chromium containing steel will drop sharply and the dimension will be unstable, so the bearing will not work properly because the chrome steel will be used more than 150 degrees. Therefore, for Jiangsu INA bearing, under the condition of working temperature of 150~350 C, if ordinary high carbon chromium Jiangsu INA bearing steel is still made in ring and rolling body, special tempering must be carried out on the bearing parts, and general tempering must be carried out. It is 50 degrees higher than the working temperature.

 

文章来自:江苏SKF轴承 www.wh-skf.com

The article comes from: Jiangsu SKF bearing www.wh-skf.com

文章来自:江苏INA轴承 www.xzahg.com

The article comes from: Jiangsu INA bearing www。ina-china。cn

文章来自:江苏NSK轴承 www.klbbearings.com

The article comes from: Jiangsu NSK bearing www.klbbearings.com

 

 

【声明】我站所发布的轴承文章,都是本公司技术原创,我公司对发布的文章拥有著作权,其余网站均不可抄袭,我公司将对抄袭的行为保留法律追究的权利。
点击次数:  更新时间:2018-07-14 17:01:03  【打印此页】  【关闭
关于我们 品牌展示
快乐飞艇怎样玩才有钱赚 快乐赛车的规律 快乐赛车怎么代理返点多少 快乐飞艇怎么样充值 快乐赛车单双 快乐赛车软件 快乐飞艇官方网站 快乐赛车计划 快乐飞艇如何购买 快乐飞艇用哪个计划