所提供的轴承产品全部品质保障。珍惜您的设备,欢迎新老客户前来订购!
联系我们
    鸿御(上海)国际贸易有限公司
    电话:021-56036899
    传真:021-56036877
    手机:13311666672
    QQ:524085168
    邮箱:china_bearing@163.com
    地址:上海市静安区共和新路425号
江苏INA轴承常用质量检测手法的实施 来源:御狮轴承   点击:次   日期:2018-07-03 11:02

安装时,应根据江苏INA轴承的载荷和工作温度确定合适的间隙值。根据轴承的尺寸和布局,轴和轴承箱的制造材料,以及两个关节轴承之间的距离,实际操作中的初始间隙可以更小或更多。

When installing, the suitable clearance value should be determined according to the load and working temperature of INA bearing in Jiangsu. According to the size and layout of the bearing, the manufacturing material of the shaft and the bearing box, and the distance between the two joint bearings, the initial clearance in the actual operation can be smaller or more.

例如,江苏INA轴承内外环的热膨胀将导致间隙在操作中变窄,因此初始间隙必须相当大,以避免轴承变形和不利后果。

For example, the thermal expansion of the inner and outer ring of the Jiangsu INA bearing will cause the gap to be narrowed in the operation, so the initial clearance must be quite large to avoid the bearing deformation and adverse consequences。

所有江苏INA轴承的间隙应达到标准,因为下部和下部的零件都超出公差,所以轴承之间的间隙不合格。如果轴承间隙过小,就会损坏接头。当轴承旋转时,挠度不灵活,容易被家人发现,因此普通轴承的间隙过大。

The clearance of all INA bearings in Jiangsu should be up to standard, because the gap between the bearing and the lower part is out of tolerance. If the clearance of the bearing is too small, the joint will be damaged. When the bearing rotates, the deflection is not flexible and easy to be found by the family members, so the clearance of the common bearing is too large.

由于一般用户没有标准的测试条件,因此可以使用塞尺来检查江苏INA轴承间隙,这是简单而有效的。轴承间隙通常很小,天线很薄,强度很低。由于轴承的结构特点,接触不容易进入轴承。

Because the general user does not have the standard test condition, therefore can use the feeler to check the Jiangsu INA bearing clearance, this is simple and effective。 The bearing clearance is usually very small, the antenna is very thin, and the strength is very low。 Because of the structural characteristics of bearings, contact is not easy to enter bearings。

当测试时,固定器可以位于两个滚轮的中间,靠近滚子的顶部和江苏INA轴承的内圈,这样皮带可以很容易地进入轴承表面。如果滚轮以适当的力滚动通过带,则测量值的一半是轴承的间隙;如果滚动体太松或太紧,则应适当调整接触件的尺寸。

When testing, the fixer can be located in the middle of the two roller, close to the top of the roller and the inner ring of the Jiangsu INA bearing, so that the belt can easily enter the bearing surface. If the roller is rolling through the belt with appropriate force, half of the measured value is the clearance of the bearing; if the roller is too loose or too tight, the size of the contact should be properly adjusted.

应该注意的是,在插入江苏INA轴承塞尺之后,如果滚轮磨损,喇叭太费力,就不必强制滚动,以免损坏塞尺。注:厚度检查时应采用多辊,厚度不应小于3。此外,滚子轴承的间隙可以用熔断器代替塞子进行检查。

It should be noted that after inserting the Jiangsu INA bearing gauge, if the roller wears and the horn is too laborious, it is not necessary to force the roll to avoid damaging the feeler gauge. Note: multi roll should be used for thickness inspection, and the thickness should not be less than 3. Besides, the clearance of roller bearings can be checked with fuses instead of stoppers.

用左手握住江苏INA轴承座,用外罩转动右手,检查轴承旋转时是否有噪音。由于假冒伪劣产品的生产条件非常落后,有些甚至是手工车间,所以在生产过程中,砂轮中的轴承不可避免地会有杂质进入和残留,噪音会变得疯狂。当轴承旋转时。这是假冒伪劣产品,严格执行生产标准和机器加工。工厂产品的最大区别。

Hold the Jiangsu INA bearing block with your left hand, turn the right hand with the outer cover, check whether there is any noise when the bearing rotates。 Because the production conditions of counterfeit and shoddy products are very backward, some are even manual workshops, so in the process of production, the bearings in the grinding wheel will inevitably have impurities to enter and remain, the noise will become crazy。 When the bearing is rotated。 This is fake and shoddy products, strictly enforce production standards and machine processing。 The biggest difference between factory products。

 

文章来自:江苏SKF轴承 www.wh-skf.com

The article comes from: Jiangsu SKF bearing www.wh-skf.com

文章来自:江苏INA轴承 www.xzahg.com

The article comes from: Jiangsu INA bearing www.xzahg.com

文章来自:江苏NSK轴承 www.klbbearings.com

The article comes from: Jiangsu NSK bearing www.klbbearings.com

【声明】我站所发布的轴承文章,都是本公司技术原创,我公司对发布的文章拥有著作权,其余网站均不可抄袭,我公司将对抄袭的行为保留法律追究的权利。
点击次数:  更新时间:2018-07-03 11:02:38  【打印此页】  【关闭
关于我们 品牌展示
快乐飞艇介绍 快乐飞艇计划软件 快乐飞艇是骗人的吗 快乐赛车作弊器 快乐赛车开奖记录 快乐飞艇官方网站 快乐赛车开奖有什么规律 快乐飞艇统一开奖吗 快乐赛车是属于彩票吗 快乐赛车是正规福彩吗