所提供的轴承产品全部品质保障。珍惜您的设备,欢迎新老客户前来订购!
联系我们
    鸿御(上海)国际贸易有限公司
    电话:021-56036899
    传真:021-56036877
    手机:13311666672
    QQ:524085168
    邮箱:china_bearing@163.com
    地址:上海市静安区共和新路425号
江苏INA轴承圆柱滚子的用途以及E型的解析 来源:御狮轴承   点击:次   日期:2018-06-17 23:12

江苏INA轴承型:一种加强结构,侧边有一个球隙,可容纳更多的球,因此具有更高的承载能力。

Jiangsu INA bearing type: a reinforced structure with a ball gap on the side, which can hold more balls and therefore has higher carrying capacity。

两侧均为防尘罩和双面密封环。双角接触球轴承设计和E型设计可具有两个江苏INA轴承防尘盖(非接触式)或密封环(接触式)。密封轴承内装有防锈锂盐,工作温度在30110度之间。在使用中没有润滑装置,也没有加热装置。

Both sides are dustproof cover and double side seal ring。 Double angle contact ball bearing design and E type design can have two Jiangsu INA bearing dust cover (non-contact) or seal ring (contact type)。 The anti rust lithium salt is installed in the sealed bearing, and the working temperature is between 30~110 degrees。 There is no lubricating device and no heating device in use。

应注意安装双列角接触球轴承,虽然轴承可承受双向轴向载荷,但如果在一侧存在间隙,则应注意主轴的主轴不应穿过间隙的边缘。

Attention should be paid to the installation of double row angular contact ball bearings, although the bearings can bear bi-directional axial load, but if there is a gap on one side, it should be noted that the spindle of the spindle should not pass through the edge of the gap.

进口铁姆肯轴承

Imported Timken bearing

高速江苏INA轴承精密角接触球轴承主要应用于轻载高速旋转场合,要求精度高、速度快、温度低、振动小、使用寿命长。高速电主轴轴承的安装经常用于高速电主轴关键零件的平面磨床上。主要技术指标:

High speed Jiangsu INA bearing precision angular contact ball bearings are mainly used in light load and high speed rotary occasions, which require high precision, fast speed, low temperature, small vibration and long service life. The installation of high speed motorized spindle bearings is often applied to the surface grinder of key parts of high-speed motorized spindle. Main technical indicators:

1。江苏INA轴承精度指标:大于GB/307.1-91精密P4

1. Jiangsu INA bearing accuracy index: greater than GB/307.1-91 precision P4

2。高性能指标:DMN1.31.8x 106min

2. High performance index: DMN value 1.3 ~ 1.8x 106 / min

三。寿命(平均值):>1500小时

Three. Life (average): > 1500 hours

江苏INA轴承轴承的使用寿命与安装有很大关系。

The service life of INA bearing bearing in Jiangsu has great relation with installation.

1。轴承应安装在一个干净、干净的房间。轴承应仔细选择。轴承应该用隔膜磨削。在保持内外环高的条件下,膜片的平行度应在1m以下。

1. Bearings should be installed in a clean and clean room. The bearings should be carefully chosen. The bearings should be grind with a diaphragm. Under the condition of keeping the inner and outer ring high, the parallelism of the diaphragm should be below 1m.

2。江苏INA轴承安装前应清洗干净,内圈向上倾斜,手部灵活,无滞流,干燥后放入规定的油中,若油雾润滑应放入少量油雾油中。

2. Jiangsu INA bearing should be cleaned before installation, the inner ring is tilted upward, hand flexible, no stagnation, after drying into the prescribed oil, if oil mist lubrication should be put in a small amount of oil mist oil.

三。轴承安装应采用特殊工具,应力均匀,不打浆。

Three. Bearing installation should adopt special tools with uniform stress and no beating.

保持清洁通风4。江苏INA轴承,无腐蚀性气体,相对湿度小于65%。腐蚀应定期腐蚀,长期保存。

Keep clean and ventilated 4. Jiangsu INA bearing, no corrosive gas, relative humidity less than 65%. Corrosion should be regularly corroded and preserved for a long time.

 

文章来自:江苏SKF轴承 www.wh-skf.com

The article comes from: Jiangsu SKF bearing www。wh-skf。com

文章来自:江苏INA轴承 www.xzahg.com

The article comes from: Jiangsu INA bearing www.xzahg.com

文章来自:江苏NSK轴承 www.klbbearings.com

The article comes from: Jiangsu NSK bearing www。klbbearings。com

【声明】我站所发布的轴承文章,都是本公司技术原创,我公司对发布的文章拥有著作权,其余网站均不可抄袭,我公司将对抄袭的行为保留法律追究的权利。
点击次数:  更新时间:2018-06-17 23:12:31  【打印此页】  【关闭
关于我们 品牌展示
快乐赛车官方计划软件 快乐赛车福利彩票 快乐赛车是正规福彩吗 快乐飞艇哪里开的 快乐飞艇杀一码的网址 快乐飞艇如何玩才稳 快乐赛车单双 快乐赛车什么方法稳 快乐飞艇怎么赢钱 快乐飞艇怎样注册